Mr-Glass Window Installation Nationwide | Sightline Windows & Doors Kendall

Mr-Glass Window Installation: The Kendall Owner’s Guide

Mr-Glass window installation in Kendall typically runs $340-$780 per opening for standard vinyl or aluminum replacements, with impact-rated units starting around $620. We stock Mr-Glass-compatible frames, sashes, and hardware for same-day installation on most residential series. Most Kendall homeowners discover a problem when the window won’t stay open, won’t lock, or they feel air moving along the frame during our summer storms.

Call (786) 321-3319

Sonia Raman and our crew have measured and set Mr-Glass units across Kendall since 2012, from the townhomes near Dadeland Mall to the single-family builds west of the Turnpike. The Haven Standard governs every opening: written price first, verified crew, documented finish.

Which Mr-Glass Models This Applies To

Mr-Glass produces three residential lines you’re likely to find in Kendall: the MG-200 vinyl single-hung series, the MG-400 aluminum impact-rated line, and the MG-600 hybrid thermal-break frames common in newer construction near Pinecrest and Palmetto Bay. The label is usually stamped into the top track of the sash or etched on the spacer bar between panes. If the label’s worn, measure the daylight opening width and height to the nearest 1/8 inch, and note whether the frame is nail-fin (new construction) or block-frame (replacement).

OEM Mr-Glass sashes and balances are available through regional distribution in Miami-Dade, with typical lead times of 3-5 business days for non-stock sizes. We also source quality aftermarket equivalents from CWS and ES Windows hardware lines when the original part is back-ordered or discontinued. The aftermarket route saves roughly 15-20% on parts but requires verification of the balance shoe depth and cam profile, which differ between MG-200 and MG-400 series. We carry both on the truck and test-fit before ordering.

Sightline Windows & Doors Kendall is an independent service provider, not affiliated with Mr-Glass.

Signs Your Mr-Glass Window Installation Is Failing

• Sash drops or won’t stay raised. The coil balance or spiral-tension mechanism has lost preload. In Kendall’s humidity, corrosion on the balance shoe is common after 8-12 years, especially in MG-200 units facing west.
• Visible gap at the meeting rail when closed. The sash has shifted on its pivot bar or the interlock weatherstrip has compressed. This shows up first on second-story windows where thermal expansion cycles are more severe.
• Condensation between panes. The insulated glass unit (IGU) seal has failed. Mr-Glass IGUs typically carry a 10-year glass warranty, but the labor to remove and reset the sash is not covered.
• Lock tongue won’t engage or spins freely. The mortise lock body has cracked or the keeper has shifted. We see this on MG-400 impact units where repeated slamming against the reinforced frame stresses the zinc housing.
• Frame corners weep water during heavy rain. The sill pan or weep holes are blocked, or the frame-to-wall sealant has separated. Kendall’s driving summer rain finds any gap; we document the water path with photos before opening the wall.

Before

After

Replacement Cost & What’s Included

These ranges include parts, labor, sealant, trim touch-up, and disposal. What moves the price: impact rating versus non-impact, custom color match versus white, and whether the existing frame is square within 1/4 inch. If it’s not, we shim and document the correction, no change order. Every job leaves with a photo record and the 365-Day Done Right Promise stamped in the Haven Standard scope.

DIY or Call Us?

What you can safely check: clear weep holes with a pipe cleaner, verify the lock keeper hasn’t loosened, and confirm the sash is fully seated in the track. These take ten minutes and cost nothing.

Where DIY goes wrong: removing a sash with a failed balance risks dropping 25-40 pounds of glass. Impact-rated IGUs weigh significantly more than standard glass, and the MG-400’s laminated pane can bind in the track if tilted incorrectly. We’ve been called to jobs where a homeowner cracked the IGU attempting to free a stuck sash, turning a $280 hardware fix into a $620 full reglaze. The balance preload on coil systems also requires a specific winding tool; improvised methods with screwdrivers have caused lacerations.

Measure once, document it, then cut. That’s how we work, and it’s why we dry-fit every sash before sealant touches glass. Call (786) 321-3319 to schedule your free estimate.

FAQs